High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

 Flat Faced Hammers

Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

• Medium-weight flat face panel beater with round point pick head designed to remove low spots when finishing

- Round Face: 38mm

- Square Face: N/A

- Head Width: 135mm

- Weight: 0.43kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does

• Medium-weight, crowned face finishing panel beater with curved pein for use where access is restricted

- Round Face: 41mm

- Square Face: N/A

- Head Width: 142mm

- Weight: 0.425kg

• Lightweight curved dolly suitable for a wide variety of panel beating tasks - reforming beads and mouldings, reshaping panels, raising low spots

- Length: 125mm

- Width: 55mm

- Depth: 37mm

- Weight: 0.90kg

• Lightweight thin toe dolly enables access in difficult to reach areas

• 1 x flat face and 1 x curved face

- Length: 115mm

- Width: 56mm

- Depth: 25mm

- Weight: 0.86kg

Anvil Dolly 054901V2

• General purpose dolly with two curved faces

- Length: 102mm

- Width: 72mm

- Depth: 62mm

- Weight: 1.40kg

• Double-ended general purpose dolly with two curved faces

- Length: 76mm
- Width: 57mm
- Depth: 58mm
- Weight: 1.15kg

• Semi-circular model, ideal for rounded and contoured panels

• 1 x flat face and 1 x convex face

- Length: 83mm

- Width: 63mm

- Depth: 36mm

- Weight: 1.08kg

• Adjustable blade holder, suitable for forming & shaping fillers and metal during body repair work
• Steel tension adjuster and base plate
• Supplied with a standard flat cut 9tpi blade
• Compatible with most flat profile 356mm body blades
• Robust construction with steel tension adjuster, sole plate and tough plastic handle
• 2 position handle for vertical or horizontal use
• Other blades also available - ask for details

• Adjustable blade holder, suitable for forming & shaping fillers and metal during body repair work
• Steel tension adjuster and base plate
• Compatible with most flat profile 356mm body blades
• Robust construction with steel tension adjuster, sole plate and tough plastic handle
• 2 position handle for vertical or horizontal use
• Individual blades available - ask for details

• Specially heat treated alloy steel provides hardness with flexibility
• Length: 356mm
• Precision cut teeth
• Blade edges chamfered
• Maximum deflection of 14mm

• Specially heat treated alloy steel provides hardness with flexibility
• Length: 356mm
• Precision cut teeth
• Blade edges chamfered
• Maximum deflection of 14mm

• Specially heat treated alloy steel provides hardness with flexibility
• Length: 356mm
• Precision cut teeth
• Blade edges chamfered
• Maximum deflection of 14mm

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

General Purpose Spoon 05740000

• Multi-purpose double ended spoon which is designed for panel beating where access is restricted and separating the outer panels from the inner frame structure

- Length: 295mm

- Width: 40mm

- Weight: 1.10kg

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

Angled Surfacing Spoon 05780000

• Multi-purpose surfacing spoon,with specially designed angled head for panel beating work in restricted areas.

For example separating outer panels from inner frame structure depending on the amount of access available

- Length: 185mm

- Width: 45mm

- Weight: 1.56kg

• Flat steel blade with serrated teeth and pvc handle

• Suitable for removing bumps,dents & flattening wavy surfaces

• Ideal for semi-finishing work on body panels

• Milled serrations help prevent metal stretch

• 350 x 35mm

• Auto-centering tool for removal of spot welds

• Adjustable centering device enables depth of cut to be controlled

• 5/16” hex shank for use with drill chucks of 3/8” capacity

• Reversible screw-on cutter blade for longer life

Spare Parts:

• 04001400 - Spare Cutters

• 04001500 - Spare Pins (x3)

Stubby Type Drill

80mm - Length

8mm - Diameter

• High speed cobalt steel drills, for removal of spot welds without distortion

• CryoCobalt™ Drills are specially designed for drilling very hard metals
• Ideal for drilling high strength alloy steels, ultra high strength boron steels,
as well as aluminium chassis, panels and rivets
• Added Cobalt increases micro-sharpness and operating temperatures
• Cryophase process improves flexibility and extends bit operating life
• CryoCobalt™ drills can be re-sharpened

Length: 105mm
Diameter: 6.5mm

Material: CM-88™ Chrome Moly Cobalt High Heat Steel
Heat Resistance: Up to 1200°F / 650°C
Hardness: 66-68Re
Tip Design: 135° Split Point
Coating: Gold Oxide
Cryophase: Patented thermal cycling cryogenic treatment

• CryoCobalt™ Drills are specially designed for drilling very hard metals
• Ideal for drilling high strength alloy steels, ultra high strength boron steels,
as well as aluminium chassis, panels and rivets
• Added Cobalt increases micro-sharpness and operating temperatures
• Cryophase process improves flexibility and extends bit operating life
• CryoCobalt™ drills can be re-sharpened

Length: 115mm
Diameter: 8mm

Material: CM-88™ Chrome Moly Cobalt High Heat Steel
Heat Resistance: Up to 1200°F / 650°C
Hardness: 66-68Re
Tip Design: 135° Split Point
Coating: Gold Oxide
Cryophase: Patented thermal cycling cryogenic treatment

Sheet Metal Cutter - 1.6mm capacity (16SWG) - Bench Mounted

• Light weight roller type cutter suitable for straight, curved and angled cutting on mild steel metal up to 1.6mm thick

• Reversible ratchet action cuts sheet metal quickly and efficiently & makes angle cutting easier

• Cutter wheels incorporate replaceable shear pins to prevent damage from overloading

• PVC Handle for operator comfort

• Replacement cutter wheels available

• Can also be vice mounted (with 04200100 - vice mounting block)

Capacity: 1.6mm (16swg)

Body: 135 x 130 x 60mm

Handle: 300 x 27 x 6mm

Wheels:  50mm dia

Weight: 1.75kg

Spare Parts:

• 04200200 - Replacement Cutter Wheels (pair)
• 04200400 - Shear Pins (2 Pack)
• 04200300 - Ratchet Wheel
• 04200500 - Repair Kit

Optional Extra:

• 04200100 - Vice Mounting Block

• Portable hand held crimping tool suitable for bending and crimping flanges when replacing door skins and body panels

• Tough, replaceable nylon pads prevent damage to door skin when crimping flanges

• Supplied 50mm wide nylon pad for faster crimping on straight edges

• High quality chrome plated tool with pvc coated handles for comfort

Length 310mm

Handles 200mm

Jaws - Width 16mm

Nylon Block 50 x 22mm

Weight  large 0.81kg

Spare Parts:

• 04310270 - 50mm Nylon Pad

Trim Tool Set

• Set of five strong, flexible plastic angled, lever and panel pullers

• Ideal for roof linings, door trims, panel trims and moulding strips

• Designed to enable the safe removal of vehicle trim panels without damage

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

• For prying, levering and panel beating in areas that are inaccessible to dollies

• Heavy duty pry spoon specially designed for separating outer panels from the inner frame structure

- Length: 405mm

- Width: 63mm

- Weight: 1.48kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Shrinking Hammers: Useful in the final stages of panel finishing when slightly stretched areas of metal can be encountered. In using this type of beater, small amounts of metal are forced into the spaces created by the cross milling. They can also be used on cold aluminium but working on sheet steel will be quicker if heat is applied to the area. Whenever possible, such beating should be carried out on the inside of the panel to minimise resurfacing needed prior to painting. Syke-Pickavant does not recommend using the same individual tools on aluminium and steel.

Panel Beater Double Ended Shrinking Hammer 05280000

• Medium-weight, flat face shrinking hammer, specifically designed for panel beating on slightly stretched areas of metal

• Specially designed cross milled heads improves stretched areas by forcing small amounts of metal into spaces created by cross milling

- Round Face: 41mm
- Square Face: 38mm
- Head Width: 97mm
- Weight: 0.425kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers: Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

• Medium-weight, flat face finishing panel beater with straight pein

- Round Face: 41mm

- Square Face: N/A

- Head Width: 130mm

- Weight: 0.425kg

• A useful addition to any bodyshop tool kit, handy when refitting rubber boot and door opening seals
- Round Faces: 28.5mm
- Hammer Size: 2
- Length: 306mm
- Weight: 1.06kg

• Convex curved grid-pattern face which assists in shrinking stretched areas of metal

- Length: 120mm

- Width: 58mm

- Depth: 28mm

- Weight: 1.16kg

• Double-ended dolly for re-shaping rounded and contoured panels

• 1 x domed and 1 x flat round surface

- Length: 56mm

- Width: 56mm

- Depth: 56mm

- Weight: 0.73kg

• Heavyweight toe dolly enables access in difficult to reach areas

• 1 x flat face and 1 x curved face

- Length: 125mm

- Width: 60mm

- Depth: 30mm

- Weight: 1.37kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers: Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

 • Medium-weight, flat face panel beater suitable for straightening thicker gauge metals where significant corrective force is required

- Round Face: 41mm

- Square Face: 38mm

- Head Width: 97mm

- Weight: 0.425kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Medium-weight, crowned face panel beater suitable for straightening thicker gauge metals where significant corrective force is required

- Round Face: 41mm

- Square Face: 38mm

- Head Width: 97mm

- Weight: 0.425kg

High quality alloy steel heads with hardened striking surfaces
• Fine quality octagonal wooden shafts fitted as standard
• Wood and steel wedged handles ensure maximum head retention with improved safety
• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers
Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Light-weight, crowned face panel beater suitable for applying measured force in area of light damage or on thinner gauge metal
- Round Face: 32mm
- Square Face: 25mm
- Head Width: 89mm
- Weight: 0.37kg

 

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Medium-weight, crowned face finishing panel beater with straight pein

- Round Face: 41mm

- Square Face: N/A

- Head Width: 130mm

- Weight: 0.425kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Crowned Faced Hammers: Crowned faced hammers are used for the same general purposes as flat faced hammers but are less likely to cause a crease if the hammer blow is not precise. The crowned face does however, produce more marked stretching around the impact area.

• Medium-weight crowned face panel beater with round point pick head designed to remove low spots when finishing

- Round Face: 38mm

- Square Face: N/A

- Head Width: 135mm

- Weight: 0.43kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers

Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

Light-weight, flat face panel beater suitable for applying measured force in areas of light damage or on thinner

gauge metal

- Round Face: 32mm

- Square Face: 25mm

- Head Width: 89mm

- Weight: 0.37kg

High quality investment casting alloy steel heads with hardened striking surfaces

• Fine quality octagonal wooden shafts fitted as standard

• Wood and steel wedged handles ensure maximum head retention with improved safety

• The heads have a tapered centre allowing the shaft to expand into the head & are secured with a double wedge

Flat Faced Hammers: Traditional flat faced hammers are designed to construct or reconstruct sheet metal vehicle components, as well as for the removal of small imperfections in sheet metal surfaces. The flat surface minimises distortion and limits the stretching effect of the hammer blow. Flat surface hammers require a high degree of precision so as not to crease the metal surface.

• Medium-weight flat face shrinking hammer, specifically designed for panel beating on slightly stretched areas of metal

• Twin head with 1 x round flat face and 1 x square, cross milled face

- Round Face: 41mm

- Square Face: 38mm

- Head Width: 97mm

- Weight: 0.425kg

• Spoons are used for bumping and prying and can also be used instead of a dolly when direct access to the rear of a panel is obstructed. The choice of spoon depends on the original contour of the metal, the amount of access available and the proposed action (i.e. roughing or levelling).

• Specially designed for panel beating work in restricted areas and for separating outer panels from inner frame structure
- Length: 295mm
- Width: 50mm
- Weight: 0.85kg

“Thatcham™ Accredited” Body Repair Tool Kit 058500TH

“The first Body Repair Tool Kit to achieve Thatcham™ accreditation”

• General purpose 13 piece set of Body Repair Tools approved by Thatcham™ for Insurance Approved Body Repair work

• Supplied in steel tool box (52800000)

• Contents:

- 052900V2 - Panel Beater Straight Pein and Finish Flat Face

- 053000V2 - Panel Beater Pick and Finishing Flat Face

- 053700V2 - Panel Beater Pein and Finish Crowned Face

- 056900V2 - Panel Beater Flat Face and Shrinking Face

- 054301V2 - Thin Curved Dolly

- 054801V2 - Thin Toe Dolly

- 055201V2 - Utility Dolly

- 05730000 - Pry & Surfacing Spoon

- 05940000 - Bumping Tool - Flat

- 05710100 - Adjustable Body Blade Holder

- 05711100 - 9tpi Standard Cut Body Blade

- 05711200 - 12tpi Fine Cut Body Blade

- 05711500 - 6tpi Plasticut Body Blade

• Large capacity deep throat clamp, with small gripping area, for awkward shapes and access

• Suitable for holding together sheet metal, body panels and other materials

• Powerful grip and deep throat ideal for handling awkward shapes encountered when welding, glueing, marking off and template making

• Small gripping area allows close up working and deep throat enables access around bulky and awkward shapes e.g. Door sills

Length: 495mm

Jaw Opening: 300mm

Jaw Width: 250mm

Throat Depth Closed: 165 - 405mm

Weight: 1.90kg