• Pulling attachment for Sykes-Pickavant bearing pullers, part numbers 09310000 and 09320000.
• Users should also use correct thread protector to fit their bearing puller.
• Supplied in carton.

Internal Reach Min - Max: 40-150mm
External Reach Max: 100mm

Use with 09310000 and 09320000 Kits* - use 09350100 screw adaptor
*Thread Protectors - When ordering an internal pulling attachment users
should also order the correct thread protectors to fit their pulling unit or bearing puller kit.

Pulling Unit Part No. 09410000 / Pulling Kit Part No. 09310000
Use thread protectors Part No. 09312000 (2)

Pulling Unit Part No. 09420000 / Pulling Kit Part No. 09320000
Use thread protectors Part No. 09322000 (2)

Pulling Unit Part No. 09430000 / Pulling Kit Part No. 09330000
Use thread protectors Part No. 09332000 (2)

• Extract components quickly and efficiently when conventional pullers cannot be used.
• Removes gears, bearings, pinions, oil seals etc.
• Can be upgraded for twin/triple leg pulling.
• Additional twin beam pulling unit available part no. 09580500.
• Supplied in metal case.

Internal Spread Min - Max: 6-60mm
No of Split Collet Extractors: 9

Contents:
08542100 1 x Slide Hammer Assembly
09580500 1 x Pulling Unit
09580900 1 x Split Collet Extractor 6.5 - 8mm
09581000 1 x Split Collet Extractor 8.5 - 10mm
09581100 1 x Split Collet Extractor 10 - 12mm
09581200 1 x Split Collet Extractor 12 - 17mm
09581300 1 x Split Collet Extractor 19 - 22mm
09581400 1 x Split Collet Extractor 22 - 30mm
09581500 1 x Split Collet Extractor 30 - 38mm
09581600 1 x Split Collet Extractor 38 - 50mm
09581700 1 x Split Collet Extractor 50 - 60mm
09582000 1 x Adaptor

 

The split collet is pushed into the centre of the bearing and then expanded
via the hex nut on the end of the collet until a secure grip is achieved.
The slide hammer is then attached providing the necessary extracting force.

Internal Spread Min - Max: 8.5-10mm

The split collet is pushed into the centre of the bearing and then expanded
via the hex nut on the end of the collet until a secure grip is achieved.
The slide hammer is then attached providing the necessary extracting force.

Internal Spread Min - Max: 50-60mm

For use with 08542100 Slide Hammer when fitting smaller sized Split Collet Extractors ( 6.5 - 30mm / 09580900 - 09581400 )

These special pullers will remove blind housing bearings without the need to dismantle machinery or remove the running shaft.

Positive seating allows even tension on inner and outer bearing rings, reducing resistance.
Stabilisers reduce sideways movement and self-centre the puller.
3 kits cover a wide range of ISO bearings. (To identify kit for bearings without an ISO reference, refer to puller spread and adaptor diameter).
Supplied in blow mould case.

Min Spread: 20mm
Max Spread: 117mm
Adaptor Dia.: 5.5-12.5mm
Puller Reach: 415mm

Internal Extractor Kit

• Extract components quickly and efficiently when conventional pullers cannot be used.
• Removes bearings, oil seals etc.

Internal Spread Min - Max: 12-17mm and 19-30mm
No. of Split Collet Extractors: 3
Upgrade: Twin beam Pulling Unit - 09580500

Internal Extractor Kit

• Extract components quickly and efficiently when conventional pullers cannot be used.
• Removes bearings, oil seals etc.

Internal Spread Min - Max: 8.5 - 17mm and 19 - 22mm
No. of Split Collet Extractors: 4
Upgrade: Twin beam Pulling Unit - 09580500

These special pullers will remove blind housing bearings without the need to dismantle machinery or remove the running shaft.

• Positive seating allows even tension on inner and outer bearing rings, reducing resistance.
• Stabilisers reduce sideways movement and self-centre the puller.
• 3 kits cover a wide range of ISO bearings. (To identify kit for bearings without an ISO reference, refer to puller spread and adaptor diameter).
• Supplied in blow mould case.

Min Spread: 20mm
Max Spread: 95mm
Adaptor Dia.: 5.5-8mm
Puller Reach: 125mm

These special pullers will remove blind housing bearings without the need to dismantle machinery or remove the running shaft.

Positive seating allows even tension on inner and outer bearing rings, reducing resistance.
Stabilisers reduce sideways movement and self-centre the puller.
3 kits cover a wide range of ISO bearings. (To identify kit for bearings without an ISO reference, refer to puller spread and adaptor diameter).
Supplied in blow mould case.

Min Spread: 56mm
Max Spread: 210mm
Adaptor Dia.: 16-31.75mm
Puller Reach: 490mm