900 Series - Twin Beam for 931 Bearing Separator Puller 205mm Long
Mechanical Separator - 10-55mm
Pullers > Separators > Separators
09500000
Brand::Sykes Pickavant
• Individual separator for removing and refitting bearings, etc. • Can be used with any of the Sykes-Pickavant design of pullers where standard legs cannot gain access. • Tapered legs provide all round support. • Supplied in carton.
External Spread Min - Max: 10-55mm
Can be used with 08300000 Twin Leg Puller or 09400000 Twin Leg Pulling Unit
Mechanical Separator - 20-105mm
Pullers > Separators > Separators
09510000
Brand::Sykes Pickavant
• Individual separator for removing and refitting bearings, etc. • Can be used with any of the Sykes-Pickavant design of pullers where standard legs cannot gain access. • Tapered legs provide all round support. • Supplied in carton.
External Spread Min - Max: 20-105mm
Use with 08310000 Twin Leg Puller or 09410000 Twin Leg Pulling Unit
Twin Beam Pulling Unit
Pullers > Separators > Pullers and Separators
09580500
Brand::Sykes Pickavant
Twin beam mechanical puller for use with Sykes-Pickavant split collet type internal extractors.
Mechanical force screw can then be used to draw extractors in place of slide hammer.
Nose Piece for 1500 Hydraulic Ram
Pullers > Separators > Pullers and Separators
15002700
Brand::Sykes Pickavant
1500 Series - Nose Piece for 1500 Hydraulic Ram
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E10
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E8
U.53H - Adaptors for threaded tips
Pullers > Separators > Adaptors
U.53H2
Mechanical External Separator Kit
Pullers > Separators > Pullers and Separators
09300000
Brand::Sykes Pickavant
With tapered edge for insertion behind close fitting bearings, gears etc.
Drop forged, high quality alloy steel, heat treated for strength and durability.
Users should also use correct thread protector to fit bearing puller.
Basic pulling units excluding the bearing separator can be supplied if required. These include a basic twin beam, screw, thrust nut, thrust race and main rod assembly. Kit No. 09300000 = Pulling Unit No. 09400000
Contents: 09301200 1 x Beam 08281100 1 x Screw / Nut Thrust 09301500 2 x Main rods, nuts & washers 09500000 1 x Separator
Mechanical Puller & Separator Kit - Thin Jaw
Pullers > Separators > Pullers and Separators
09300500
Brand::Sykes Pickavant
Pulling unit with small capacity separator and thin jaw legs will remove bearings inaccessible to standard puller jaws.
Contents: 08281100 1 x Forcing Screw 08601400 2 x Leg 75mm - Thin Jaw 09301200 1 x Beam Twin 09301500 2 x Main Rod 09500000 1 x Separator 10-55mm
Mechanical External Separator Kit
Pullers > Separators > Pullers and Separators
09310000
Brand::Sykes Pickavant
With tapered edge for insertion behind close fitting bearings, gears etc. Drop forged, high quality alloy steel, heat treated for strength and durability. Users should also use correct thread protector to fit bearing puller. Each kit supplied in metal case.
Basic pulling units excluding the bearing separator can be supplied if required. These include a basic twin beam, screw, thrust nut, thrust race and main rod assembly. Kit No. 09310000 = Pulling Unit No. 09410000
Contents: 09311200 1 x Beam 09311100 1 x Screw / Nut Thrust 09312100 1 x Thrust race 09311500 2 x Main rods, nuts & washers 09312300 2 x 5" Extension Rods 09311900 4 x Extension Rods 09510000 1 x Separator
Kit can be upgraded for internal pulling by adding 09350000
Mechanical External Separator Kit
Pullers > Separators > Pullers and Separators
09320000
Brand::Sykes Pickavant
With tapered edge for insertion behind close fitting bearings, gears etc. Drop forged, high quality alloy steel, heat treated for strength and durability. Users should also use correct thread protector to fit bearing puller. Each kit supplied in metal case.
Basic pulling units excluding the bearing separator can be supplied if required. These include a basic twin beam, screw, thrust nut, thrust race and main rod assembly. Kit No. 09320000 = Pulling Unit No. 09420000
Contents: 09321200 1 x Beam 09321100 1 x Screw / Nut Thrust 09322100 1 x Thrust race 09321500 2 x Main rods, nuts & washers 09322300 2 x 5" Extension Rods 09321900 4 x Extension Rods 09520000 1 x Separator
Kit can be upgraded for internal pulling by adding 09350000
Twin Beam for Mechanical Puller
Pullers > Separators > Pullers and Separators
09321200
Brand::Sykes Pickavant
900 series - Twin Beam for 932 Bearing Separator Puller 290mm Long M24
Thread protector - 38mm long
Pullers > Separators > Pullers and Separators
09322000
Brand::Sykes Pickavant
Thread Protector - 38mm Long (5/8” x 14 BSF) When ordering an internal pulling attachment users should also order the correct thread protectors to fit their pulling unit or bearing puller kit.
For use with: Pulling Unit Part No. 09420000 Pulling Kit Part No. 09320000
internal race extractor
Pullers > Separators > Pullers and Separators
09360000
Brand::Sykes Pickavant
Pulling attachment for Sykes-Pickavant bearing pullers, part number 09330000. Users should also use correct thread protector to fit their bearing puller. Supplied in carton.
Internal Reach Min - Max: 75-230mm External Reach Max: 150mm
Use with 09330000 Kit* - Use screw adaptor 09360100 *Thread Protectors - When ordering an internal pulling attachment users should also order the correct thread protectors to fit their pulling unit or bearing puller kit.
Pulling Unit Part No. 09410000 / Pulling Kit Part No. 09310000 Use thread protectors Part No. 09312000 (2)
Pulling Unit Part No. 09420000 / Pulling Kit Part No. 09320000 Use thread protectors Part No. 09322000 (2)
Pulling Unit Part No. 09430000 / Pulling Kit Part No. 09330000 Use thread protectors Part No. 09332000 (2)
Pulling Unit
Pullers > Separators > Pullers and Separators
09400000
Brand::Sykes Pickavant
900 Series - Pulling Unit for use with 09500000 Separator Comprises: Twin Beam, Screw and Pulling Rods (2)
Suitable for use with 19310500, 15530500
Mechanical Puller & Separator Kit - Multi Puller Pack
Pullers > Separators > Pullers and Separators
09400300
Brand::Sykes Pickavant
• Makes 5 different mechanical puller/separator combinations. • Consists of a thin jaw puller, reversible leg puller and separator the ideal combination for light applications. • Supplied in carton
Contents 08281100 1 x Forcing Screw 08601400 2 x Leg 75mm - Thin Jaw 09301200 1 x Twin Beam 09301500 2 x Main Rod 08271100 1 x Forcing Screw 09500000 1 x Separator 10-55mm 08271200 1 x Twin Head 08271300 1 x Triple Head 08271400 3 x Leg - Double Ended Reversible
Mechanical Internal Extractor Kit
Pullers > Separators > Pullers and Separators
09450000
Brand::Sykes Pickavant
For the extraction of bushes, sleeves and bearings from blind housings, when the centre shaft has been removed and does not allow the use of a mechanical puller.
• Individual separators for removing and refitting bearings, etc. • Can be used with any of the Sykes-Pickavant design of pullers where standard legs cannot gain access. • Tapered legs provide all round support. • Supplied in carton.
External Spread Min - Max: 35-140mm
Can be used with 08320000 & 08330000 Twin Leg Pullers or 09420000 Twin Leg Pulling Unit
Mechanical Separator - 50-175mm
Pullers > Separators > Pullers and Separators
09530000
Brand::Sykes Pickavant
• Individual separators for removing and refitting bearings, etc. • Can be used with any of the Sykes-Pickavant design of pullers where standard legs cannot gain access. • Tapered legs provide all round support. • Supplied in carton.
External Spread Min - Max: 50 - 175mm
Can be used with Sykes-Pickavant ‘Loadstar’ Heavy Duty Pullers or 09430000 Twin Leg Pulling Unit
Hydraulic Puller & Separator Kit
Pullers > Separators > Pullers and Separators
15520800
Brand::Sykes Pickavant
Hydraulic 1500 series
Makes 6 different twin/triple leg pullers, plus bearing separator kit.
Supplied in lockable metal case.
Puller Spread Min - Max: 50-200mm Puller Reach Max: 200mm External Spread Min - Max: 20-105mm External Reach Max: 876mm
Contents: 15000000 1 x Hydraulic Ram With Nose Piece 15241200 1 x Twin Head 15341300 1 x Triple Head 15242200 1 x Ram Extension - 50mm 15262400 1 x Ram Extension - 100mm 15242400 3 x Legs - 100mm 15262600 3 x Legs - 150mm 15282800 3 x Legs - 200mm 19311200 1 x Twin Beam 09510000 1 x Separator 20-105mm 09311500 2 x Main Rods 09311900 4 x Extension Rods 09312300 2 x Extension Rods 5 inch
Contents: 15000000 1 x Hydraulic Ram With Nose Piece 15262400 1 x Ram Extension - 100mm 19311200 1 x Twin Beam 09510000 1 x Separator 20-105mm 09311500 2 x Main Rods 09311900 4 x Extension Rods 09312300 2 x Extension Rods 5 inch
Hydraulic Puller & Separator Kit - Thin Jaw
Pullers > Separators > Pullers and Separators
19310300
Brand::Sykes Pickavant
Combination pack consisting of a medium duty hydraulic thin jaw puller and bearing separator.
Also available without hydraulic ram as kit 19310400 (in carton).
Contents: 15000000 1 x Hydraulic Ram With Nose Piece 15262400 1 x Ram Extension - 100mm 08611400 2 x Legs 150mm - Thin Jaw 19311200 1 x Twin Beam 09510000 1 x Separator 20-105mm 09311500 2 x Main Rods 09311900 4 x Extension Rods 09312300 2 x Extension Rods 5 inch
Hydraulic Internal Extractor/ Puller & Separator Kits with Slide Hammer/ on Panel
Pullers > Separators > Pullers and Separators
19310500
Brand::Sykes Pickavant
Hydraulic 1500 series
For removing bearings, gears etc. where access behind components is too restricted to use standard pullers.
Drop forged, high quality steel, heat treated for strength and durability.
Extract components quickly and efficiently when conventional pullers can not be used.
Slide Hammer with 7 split collet internal extractors
Supplied in display/storage panel - 610mm x 457mm
External Spread Min - Max: 10-105mm Internal Reach Min - Max: 6-38mm External Reach Max: 876mm
Contents: 15000000 1 x Hydraulic Ram With Nose Piece 19311200 1 x Twin Beam 08601400 2 x Legs 75mm - Thin Jaw 09500000 1 x Separator 10-55mm 09510000 1 x Separator 20-105mm 09311500 2 x Main Rods 09311900 4 x Extension Rods 09312300 2 x Extension Rods 5 inch 09350000 1 x Internal Race Extractor 08542100 1 x Slide Hammer 09580900 1 x Split Collet Extractor 6.5 - 8mm 09581000 1 x Split Collet Extractor 8.5 - 10mm 09581100 1 x Split Collet Extractor 10 - 12mm 09581200 1 x Split Collet Extractor 12 - 17mm 09581300 1 x Split Collet Extractor 19 - 22mm 09581400 1 x Split Collet Extractor 22 - 30mm 09581500 1 x Split Collet Extractor 30 - 38mm 09582000 1 x Adaptor 09400000 1 x Pulling Unit 15512800 1 x Metal Panel 19312900 1 x Hook Kit
Twin Beam for Hydraulic Puller 210mm long
Pullers > Separators > Pullers and Separators
19311200
Brand::Sykes Pickavant
Twin Beam - 210mm long 1½” Dia. Internal
See Downloads section for Kit Contents List
Hydraulic Separator Kit - Heavy Duty
Pullers > Separators > Pullers and Separators
19320000
Brand::Sykes Pickavant
Hydraulic 1500 series
Versatile tool where a long reach is required to draw a bearing from a shaft.
Also available without hydraulic ram as kit 19310100 (in carton).
The tapered edges of the bearing separator provide all round support and can fit behind bearings where normal puller legs cannot gain access.
Contents: 15000000 1 x Hydraulic Ram With Nose Piece 15272600 1 x Ram Extension - 150mm 19321200 1 x Twin Beam 09520000 1 x Separator 35-140mm 09321500 2 x Main Rod 09321900 4 x Extension Rod 09322300 2 x Extension Rod 5 inch
Leg Extension incl. Pins & Nuts
Pullers > Separators > Pullers and Separators
20019200
Brand::Sykes Pickavant
Leg Extension incl. Pins & Nuts for Loadstar "Plus" 20T, 30T and 50T kits
Loadstar Press Frame
Pullers > Separators > Pullers and Separators
20039500
Brand::Sykes Pickavant
Loadstar Press Frame Assembly
460 x 165mm max / 365 x 165mm min Max Pushing Pin Diameter : 50mm Max Pushing Pin length : 150mm (when used with 20012000 hydraulic cylinder) For use with 20012000 Loadstar 20 tonnes Hydraulic Cylinder
U.23K-U.53K - Tapped beams
Pullers > Separators > Beams
U.23K1A
- Tapped beams are used in mechanical pulling with separators spherical or threaded tips.
- Spread: - 25 to 400 mm.
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E12
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E14
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E4
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E5
U.53E - Threaded tips
Pullers > Separators > Threaded Tips
U.53E6
U.53H - Adaptors for threaded tips
Pullers > Separators > Adaptors
U.53H1
U.53H - Adaptors for threaded tips
Pullers > Separators > Adaptors
U.53H3
60 mm separator and beam puller kit
Pullers > Separators > Separator and Beam Puller Kit
U.53J1
- Comprising:
- 1 separator U.53T1 = spread: - 5 to 60 mm.
- 1 beam U.53K1 = spread: - 40 to 110 mm.
- Max reach: 180 mm.
- 4 pairs of U.53E threaded tips M4 - M5 - M6 - M8.
- 2 adaptors U.53H1.
- Supplied in plastic case BP.112 with tray PL.296A.
Weight: 3.400 kg.
110 mm separator and beam puller kit
Pullers > Separators > Separator and Beam Puller Kit
U.53J2
- Comprising:
- 1 separator U.53T2 = spread: - 15 to 110 mm.
- 1 beam U.53K2 = spread: - 70 to 200 mm.
- Max reach: 240 mm.
- 4 pairs of U.53E threaded tips M8 - M10 - M12 - M14.
- 2 adaptors U.53H2.
- Supplied in plastic case BP.109 with tray PL.297A.
Weight: 7.300 kg.
U.23K-U.53K - Tapped beams
Pullers > Separators > Beams
U.53K1
- Tapped beams are used in mechanical pulling with separators spherical or threaded tips.
- Spread: - 25 to 400 mm.
U.23K-U.53K - Tapped beams
Pullers > Separators > Beams
U.53K2
- Tapped beams are used in mechanical pulling with separators spherical or threaded tips.
- Spread: - 25 to 400 mm.
U.23K-U.53K - Tapped beams
Pullers > Separators > Beams
U.53K3
- Tapped beams are used in mechanical pulling with separators spherical or threaded tips.
- Spread: - 25 to 400 mm.
U.23K-U.53K - Tapped beams
Pullers > Separators > Beams
U.53K4
- Tapped beams are used in mechanical pulling with separators spherical or threaded tips.
- Spread: - 25 to 400 mm.
U.53KL - Non-tapped beams
Pullers > Separators > Beams
U.53KL2
- Non tapped beams allow to use clamps U.49P1 to U.49P9 to extract bearings by inside grip.
- U.53KL0: for clamps U.49P1 to U.49P4.
- U.53KL2: for clamps U.49P5 to U.49P9 with adaptor tip U.49BR1.
U.23K-U.53RL - Spare tie rods for beam
Pullers > Separators > Beams
U.53R1L
- Tie rods supplied by 2 with chrome-plated tips nuts and washers.
U.23K-U.53RL - Spare tie rods for beam
Pullers > Separators > Beams
U.53R2L
- Tie rods supplied by 2 with chrome-plated tips nuts and washers.
U.23K-U.53RL - Spare tie rods for beam
Pullers > Separators > Beams
U.53R3L
- Tie rods supplied by 2 with chrome-plated tips nuts and washers.
U.23K-U.53RL - Spare tie rods for beam
Pullers > Separators > Beams
U.53R4LA
- Tie rods supplied by 2 with chrome-plated tips nuts and washers.
U.53S - Jack beams
Pullers > Separators > Beams
U.53S2A
- These 2 non tapped beams with mechanical specifications exceeding U.53K (dimensions steel and thermal treatment) are designed to withstand the high loads generated by the power of jacks used.
U.53S - Jack beams
Pullers > Separators > Beams
U.53S4A
- These 2 non tapped beams with mechanical specifications exceeding U.53K (dimensions steel and thermal treatment) are designed to withstand the high loads generated by the power of jacks used.
U.53T - Separators
Pullers > Separators > Separators
U.53T1
- Separators spread - 5 to 250 mm.
- Fit behind races where ordinary puller claws will not reach.
- They can be used with beams assisted by screws or jacks.
U.53T - Separators
Pullers > Separators > Separators
U.53T2
- Separators spread - 5 to 250 mm.
- Fit behind races where ordinary puller claws will not reach.
- They can be used with beams assisted by screws or jacks.
U.53T - Separators
Pullers > Separators > Separators
U.53T3
- Separators spread - 5 to 250 mm.
- Fit behind races where ordinary puller claws will not reach.
- They can be used with beams assisted by screws or jacks.
U.53T - Separators
Pullers > Separators > Separators
U.53T4
- Separators spread - 5 to 250 mm.
- Fit behind races where ordinary puller claws will not reach.
- They can be used with beams assisted by screws or jacks.
U.53T - Separators
Pullers > Separators > Separators
U.53T5
- Separators spread - 5 to 250 mm.
- Fit behind races where ordinary puller claws will not reach.
- They can be used with beams assisted by screws or jacks.
